quote:Olds: whats initial and total timing? What camshaft?
I do not remember what number this camshaft, and changed a few times, look at a box in the garage and write.
Now I have installed like this rastpredval, he stayed with me from the previous engine.
Part Number: 113941 Grind Number: H-268-2 (REPLACES H-272-2)
Engine Identification:
Start Yr. End Yr. Make Cyl Description
1957 1987 CHEVROLET 8 GOOD IDLE, FOR 350+ CU. IN. MODIFIED ENGINES WITH FREE-FLOWING ABOVE WATER EXHAUST SYSTEMS FOR PERFORMANCE APPLICATIONS IN LIGHT PLEASURE AND SKI BOATS, INCLUDING JET BOATS, 8.75 TO 10.75 COMPRESSION RATIO ADVISED (C.A.R.B. E.O. D-225-18). BASIC RPM 2000-5000
Engine Size Configuration
262-400 C.I. V
Valve Setting: Intake .000 Exhaust .000 HOT
Lift: Intake @Cam 306 @Valve 459 All Lifts are based
on zero lash and theoretical rocker arm ratios.
Exhaust @ Cam 324 @Valve 486
Rocker Arm Ratio 1.50
Spring Requirements: Triple Dual Outer Inner
Part Number 99848
Loads Closed 105 LBS @ 1.700 or 1 45/64
Open 280 LBS @ 1.240
Recommended RPM range with matching components
Minimum RPM 2000
Maximum RPM 5000
Valve Float 6500
Tähistame teeninud ......Is it flat tappet cam? If so then I really hope you didnt ruined your camshaft...If that was first start and you let motor idle you ruined your camshaft Iam more than sure about it. NEVER let motor idle with new flat tappet cam!
Have you heard about camshaft "brake in" procedure?
quote:Olds: Is it flat tappet cam? If so then I really hope you didnt ruined your camshaft...If that was first start and you let motor idle you ruined your camshaft Iam more than sure about it. NEVER let motor idle with new flat tappet cam!
Have you heard about camshaft "brake in" procedure?
I did not understand a bit, but what shaft to put it?
quote:Olds: Is it flat tappet cam? If so then I really hope you didnt ruined your camshaft...If that was first start and you let motor idle you ruined your camshaft Iam more than sure about it. NEVER let motor idle with new flat tappet cam!
Have you heard about camshaft "brake in" procedure?
I did not understand a bit, but what shaft to put it?
quote:Olds: Is it flat tappet cam? If so then I really hope you didnt ruined your camshaft...If that was first start and you let motor idle you ruined your camshaft Iam more than sure about it. NEVER let motor idle with new flat tappet cam!
Have you heard about camshaft "brake in" procedure?
I did not understand a bit, but what shaft to put it?
I need to install a different shaft?
Yes, I know that the first 15 minutes at idle and then an oil change and so delee ..... thanks for predsterezhenie ...
in the near future, I want to buy a camshaft 1500-6500 and aluminum heads.
Tähistame teeninud ......15min to idle, are you grazy!? You ruined your camshaft allready! Prepare to order new cam AND lifters and before fireing up motor with new camshaft read how you have to make "cam break-in" : http://4secondsflat.com/Hydraulic_lifter_cams.html
NEVER ALLOW ENGINE TO IDLE!!!
quote:Olds: 15min to idle, are you grazy!? You ruined your camshaft allready! Prepare to order new cam AND lifters and before fireing up motor with new camshaft read how you have to make "cam break-in" : http://4secondsflat.com/Hydraulic_lifter_cams.html
NEVER ALLOW ENGINE TO IDLE!!!
This shaft and lifters are not new, he was standing on this engine, but with a different crankshaft. I used this to substituted camshaft crankshaft, pistons and connecting rods.
I'm on this camshaft has traveled many many miles, I think that will happen to him all right.
quote:Olds: 15min to idle, are you grazy!? You ruined your camshaft allready! Prepare to order new cam AND lifters and before fireing up motor with new camshaft read how you have to make "cam break-in" : http://4secondsflat.com/Hydraulic_lifter_cams.html
NEVER ALLOW ENGINE TO IDLE!!!
This shaft and lifters are not new, he was standing on this engine, but with a different crankshaft. I used this to substituted camshaft crankshaft, pistons and connecting rods.
I'm on this camshaft has traveled many many miles, I think that will happen to him all right.